Activity Stream

I picked up this 200X from a family member. It has spent the better part of the last 15 years outside...neglected and left for dead. I remember...

Its time to try something different.

this is the place to start a new build, to much gets lost on the pages! so lets have a little fun again, its been a while since i have used the...

I glad the the jurors saw thru all of the prosecutions B.S., although I really think the judge should have slapped the prosecutions peepee. Of...

Not sure if anyone has seen this before but I had some 80's nostalgia music playing and I spied some gems around the 2:00 minute mark. I don't...

Okay folks need some help. We have a ATC 90 Bored 5mm over, stroked, ported head, bigger cam, heavy duty valve springs. The machine smokes bad, runs...

YouTube (owned by Google) no longer allows the public to view the video and comment dislike counts, site wide. Buh-bye YouTube.

Hi everyone, I recently put new rear tires on my 250ES (Bear Claws are awesome!). They're a little bigger than what was on there before, so they...

so the 200x frame got traded off this morning. I traded it for a 200s project, its pretty complete, no tank, had axle. So as we are shooting the...

going to meet the kids tomorrow to ride, had to move 1 and 3/4 trikes from behind the chevelle to move the chevelle so I could get to the 350x. ...

I have a 79 xl250 honda and 77 yz250 that I am considering trading for a 84 250r. xl250 has motor apart, needs rop end assembled, but I have the...

I am working on putting together some videos of a total restoration and engine top end rebuild I did on a 1984 ATC 110 not long ago. I'll post...

I always wondered if anyone ever attempted or has done a 250x engine swap into a 1st/2nd gen 200x??? I think you would have better luck in the 2nd...

I see the o rings for the 3 lug split rims on ebay for a couple bucks. But not having luck finding cheap 4 lug o rings. anyone have a link to the...

I have 2 trikes from 1984, a 200M and a 200ES. Both have recently not started and I'm thinking the colder weather here in Ga may have been a factor. ...

Hello everyone! I have a 1985 (I think) 250ES Big Red that has been in the family since pretty much new. It's been stored outside a number of...

My original plan was to modify a 200X supertrapp to use on my 200M. Well, I'm running out of time and patience. Used to be able to find DG pipes...

Hi Everyone, Just wondering if anyone has used the Chinese replacement cdi units for the 1985 Atc250r that are sold on eBay, it seems to fit a lot...

Picked up this 85 250sx bike for parts and somethings not jiving. Anyone know what or where this swingarm or drum came from? Sent from my SM-G998U...

Easy way to wind the coil back up using a vice and a pair of needle nose. https://www.youtube.com/watch?v=tXbXiuwcxx4

I have the back wheels sourced but I need a one piece wheel in good condition I believe the bolt spacing is 4/130. The offset needs to be centered to...

Hey Guys, I've got a wet side crank seal oil leak on my '84 R. Can the crank case cover be taken off with the engine in the frame? Look tight...

I got an LT80 in non running condition and put it aside for a later project. A couple days ago I rolled it into the shop to start working on it as...

Good evening, I recently bought some bandito 90 frames and looking for some parts to finish them up. I’m looking for 3 Heavy duty axles 3...

In 1996 My Dad (Rest In Peace) bought me 2 brand new Ohtsu oem atc 70 tires from the Honda dealer!!!! I have had my atc 70 ever since.. never really...

:( https://longhornengineer.com/category/motoring/honda-atc110/

Are there any aftermarket full systems out there for these trikes? I don't want anything loud, just something close to OEM if anyone makes them....

Hello. While I joined in 2015, I'll actually be spending some time here now that I have started a 3 wheeler project. I'm designing and...

Hello all, I have recently acquired an old steering stabilizer. It was removed from a first gen 200X but I believe the shock body is the same for...