Parts interchangability between 83 200e and 84 200es

[ATC250ES]

Hi,
I have a 83 200e and a 84 200es I am doing some work on and from my research and crossing part numbers the front forks and shocks are the same between the two correct? Also the seat is the same except for the 83 had a metal pan and the 84 has a white plastic bottom where it mounts to the frame? Is there someone maybe here or a good source for obtaining parts for these other than eBay? I have ordered what I could from the dealer but a number of things are no longer available.

Thanks,
Eddie

[Flossyb20]

What do you need?

[ATC250ES]

These are a few of the known things I need as of now for the 84 200es. I believe these are the correct item numbers and part numbers.


008 BAND, INSULATOR
16223-317-000 This is the clamp that fits on the connecting tube for the carb. Need screw with clamp.


010 GUIDE, BRAKE CABLE
45467-958-020 (replaces 45467-958-010) This is the guide that connects to the front fork. Need screw and nut that goes with clamp.


019 WASHER, EX. DUCT
90504-567-000 This is the washer at the rear of the gas tank mount.


014 HOLDER, TOOL
83501-958-680 Tool holder that fits under seat. Need wing bolt also.


010 CAP, PROTECTOR
24723-969-003 Use up to Engine SN 6090043 This is the cap that fits on the HI, LO, Rev Lever.
24723-969-023 Use from Engine SN 6090044


010 GROMMET, RR. FENDER
80161-958-680


016 RUBBER
80219-958-681 This is the rubber cushion that mounts to the very rear of the tool box. It shows to be a different part # than those for the sides.


018 COVER
32411-MB2-000 Positive battery cable cover.


023 CVR, MAGNETIC SWITCH
35857-969-000 Cover for the magnetic starter switch.


020 NUT, FLANGE (6MM)
94050-06080 Fits air intake to carb qty 2

[ngunter2]

Most of these odds and end are on online oem parts shops. Have you looked at any? I like partzilla for the little things under ten bucks because the dont have flat rate shipping. Anything else there are tons of these websites out there

[Flossyb20]

ooohhhhh, is this a full-on resto you're doing? BTW, none of the parts he mentioned are available anymore...

[kb0nly]

Yeah those are all hard parts to come by sadly... I have researched the 200ES to death, i own one and have worked on two others, all the parts you seek are going to have to be used or improvised from available parts on other models.

The band clamp for the carb is available for some later Honda dirt bikes, last time i needed one i took one with to the local powersports dealer and he dug around the parts bins until he found one the same diameter and width, i don't honestly know what it was made to fit but it looks almost the same as the original.

The tool holder that fits the plastic seat pan shows up on eBay, as do some of the other misc parts. The one your going to be stuck on is that cap for the sub trans shifter, they are unobtanium... So is the knob for the sub trans lever, mine broke, i searched for months, i finally ended up making a suitable replacement from a universal knob from a hardware store.

[ATC250ES]

Yea I guess you could say that. Trying to get it back as accurately as I can. I would also like to be able to find all the informational decals but no luck with that so far either. I see you can buy the stripe kit on eBay but not the others. I believe the two 6 mm flange nuts are still available I just forgot to include them in my order this last go around.

[Howdy]

I may just have a bunch of these parts ( used ). I will have to check on them.

kbOnly, you never ask me about that knob. geesh. LOL just ribbing you.
Howdy