I can help on small parts powdercoating. I'm not set up for frames or swingarms at the moment, but I can do just about everything else.
I can help on small parts powdercoating. I'm not set up for frames or swingarms at the moment, but I can do just about everything else.
'86 ATC 250R, Build Thread http://www.3wheelerworld.com/showthr...highlight=250r
'86 "Factory Tri racing" Tri-Z http://www.3wheelerworld.com/showthr...b-Top-Tank-ect
Pile of Tecate Parts
My Feedback Thread: http://www.3wheelerworld.com/showthr...edback-for-bkm
[QUOTE=atc007;1307332]No big deal. But I would love to help. I have had bikes stolen and KNOW 1st hand the pain these low life maggot sucking,good for nothing sewer swimming scumbags cause.[QUOTE]
atc007,
Your Killin' Me!!!!! Too Funny!!! I appreciate the gesture, but I'm not sure what I would need?? The inverts would have been soooo cool, but I got a good set of oem's that I think are going to do just fine.....
Hey you guys know I was asking for input on what color scheme I should do? I was thinking that I may follow what ATC250RLEN had previously done with the bike, and I never got any input from anyone on here...... BUT I saw a posting the other day that had a 200x with carbon fiber fenders....... RADICAL!!! I know if I had a set of those I would try to do some thing special with them....So I called Meier and found out they do the Carbon Fiber sets whenever they get bad plastic, and they had just ran a set, but not for the 250r..... They told me to call back this next week and see if they get anymore ran through..... they are pretty cheap too, so I think I may go that route. I will keep everyone posted on the fenders and what I decide to do.
Today I went down to Jacksonville Fl. and I found a shop down there that is willing to powder coat my frame for $150 or maybe even less!! Now the question that everyone is probably wondering is.... WHAT COLOR??? Well......... I went with the standard Red! There are just too many possibilities with this color..... I could still follow his color scheme, I could use the carbon fiber fenders, I could go with black fenders, or I could go back to the original ALL red.... which I truly love, and that was also the color scheme my bike had that was stolen......
NOW FINALLY for a little work today..... Yaeger, after I started looking at all the stuff I wanted to polish, I knew it would be WAY TOO MUCH to send out to have done, so I went down and bought a bench grinder, and a polishing wheel....... This is where I am at thus far, I do have work to do still to get them where I want them, BUT....... What do you guys think???
[QUOTE=stubbie1111;1307364][QUOTE=atc007;1307332]No big deal. But I would love to help. I have had bikes stolen and KNOW 1st hand the pain these low life maggot sucking,good for nothing sewer swimming scumbags cause.Nice work. The only problem with the bench grinder is it doesn't turn at high enough RPM to cut the aluminum and give it a luster. Other than that I think it did a damn fine job!
atc007,
Your Killin' Me!!!!! Too Funny!!! I appreciate the gesture, but I'm not sure what I would need?? The inverts would have been soooo cool, but I got a good set of oem's that I think are going to do just fine.....
Hey you guys know I was asking for input on what color scheme I should do? I was thinking that I may follow what ATC250RLEN had previously done with the bike, and I never got any input from anyone on here...... BUT I saw a posting the other day that had a 200x with carbon fiber fenders....... RADICAL!!! I know if I had a set of those I would try to do some thing special with them....So I called Meier and found out they do the Carbon Fiber sets whenever they get bad plastic, and they had just ran a set, but not for the 250r..... They told me to call back this next week and see if they get anymore ran through..... they are pretty cheap too, so I think I may go that route. I will keep everyone posted on the fenders and what I decide to do.
Today I went down to Jacksonville Fl. and I found a shop down there that is willing to powder coat my frame for $150 or maybe even less!! Now the question that everyone is probably wondering is.... WHAT COLOR??? Well......... I went with the standard Red! There are just too many possibilities with this color..... I could still follow his color scheme, I could use the carbon fiber fenders, I could go with black fenders, or I could go back to the original ALL red.... which I truly love, and that was also the color scheme my bike had that was stolen......
NOW FINALLY for a little work today..... Yaeger, after I started looking at all the stuff I wanted to polish, I knew it would be WAY TOO MUCH to send out to have done, so I went down and bought a bench grinder, and a polishing wheel....... This is where I am at thus far, I do have work to do still to get them where I want them, BUT....... What do you guys think???
Sorry guys......working another deal here....
looking pretty fresh
SEAT COVER IS DONE...... Got the swing are dis-assembled and it along with some other parts are ready for Powder coating.
WELL HERE'S AN UPDATE..... I FINALLY HAD A COUPLE OF NIGHTS WHERE I COULD GO AN SPEND A FEW HOURS IN THE GARAGE.... WIRING HARNESS INSTALLED ALONG WITH ENGINE MOUNTED..... SWINGARM INSTALLED WITN ALL NEW BEARINGS AND CHAIN GUARD. BEARING CARRIER INSTALLED WITH NEW BEARINGS, BRAKE CALIPER INSTALLED AND AXLE INSTALLED. WE MOUNTED THE REAR SHOCK AND LINKAGE AND FINALLY THE RADIATOR BRACKETS. HERE ARE SOME UPDATES PICS.... LET ME KNOW WHAT YOU THINK.... I SHOULD HAVE A ROLLER HERE SOON!!!
lookin good sir!
________________
I'm just a squirrel "Trying" to get a nut!
Nearly every kind of Honda ATC (plus some custom ones
several Yami Quads (mostly custom built for MX racing)
https://www.mikesatvfix.com
"Freedom is not free...but the U.S. Marine Corps will pay most of your share."