73 atc 7084 ytm 200ern79 atc 70ytm 225 dratc 90
80 atc 110klt 250A84 atc 200es
85 atc 250es
gone but not forgotten restored 82 atc 70
Jake 200es fenders boxed up and ready to be delivered. $400 for shipping! But i dont care finally got a set.
73 atc 7084 ytm 200ern79 atc 70ytm 225 dratc 90
80 atc 110klt 250A84 atc 200es
85 atc 250es
gone but not forgotten restored 82 atc 70
Yeah I would have paid a bit more, mike from vintage motors said he put in wooden box so it wouldn't get damaged! I'll send pics when they arrive! Ps that tri z is still available, I rang the guy today! Good news but after buying these fenders and nos mudflaps, also building a new 2 story house ahhhhhh trike or house ha ha!
Yeah I would prefer the trike! Hahah!
Ok today wasn't very successful I blew up 2 2strokes in 2 hours!! the first was a suzuki dirt bike I was about to sell that didn't worry me to much since it was really only a beater but then I pulled out red devil and went for a ride all was going good and then after about 15 mins I heard a clunk clunk and as I went to shut her off she locked up so I just gently tried to kick it over and it moved one click and then it just locked up solid no movement at all!! so I had to get dad to tow me back at first dad thought the gearbox may have locked up but the oil was clean and everything then we thought it may have snapped the rod but the case is all intact and it didn't make any really loud noises!! its not running lean I am running 40:1 looking through the spark plug hole the piston looks good from what I could see so im going to put my freshly rebuilt engine in tomorrow that I got with the bike and I will pull this one apart and check it out I think it pinched a ring!! any opinions??
73 atc 7084 ytm 200ern79 atc 70ytm 225 dratc 90
80 atc 110klt 250A84 atc 200es
85 atc 250es
gone but not forgotten restored 82 atc 70
Ok I opened the motor up and I think it was my fault since it looks like the piston has grabbed so I'm putting my spare motor in now so a couple of questions what oil to run what ratio and how do I run it in since I've never run in a 2 stroke before!!
73 atc 7084 ytm 200ern79 atc 70ytm 225 dratc 90
80 atc 110klt 250A84 atc 200es
85 atc 250es
gone but not forgotten restored 82 atc 70
Normal 2 stroke oil will work. Not sure on the ratio, I'm not extremely experienced with 2 strokes.
Ok im quite confused now I have been doing a lot of reading and everyone says run 32:1 or 40:1 now I am confused what caused my motor to seize up since I was running 40:1 clean air filter slightly rich mixture and when I opened it up there is 4 places where the piston has grabbed in each corner of the cylinder!! WHy did this happen cause I do not want this to happen to my fresh motor!! even this one has just been rebuilt so I was a little pissed!!
73 atc 7084 ytm 200ern79 atc 70ytm 225 dratc 90
80 atc 110klt 250A84 atc 200es
85 atc 250es
gone but not forgotten restored 82 atc 70
There's your problem "corners in a cylinder" sorry but I couldnt resist myself on that one. It's a mechanical type thing but do you let it get to operating temp before you take off wide open?? 2 strokes don't seem to like that
you know whats right therefore you know what is expected