I'm looking for pics of where to put the labels on the 86 Tecate frame. Not the ones on the plastics.
Thanks in advance
At The Back Of The Pack
Arm chair racerAt the back of the pack
I'm looking for pics of where to put the labels on the 86 Tecate frame. Not the ones on the plastics.
Thanks in advance
3 86 Tecate 3
1 87 tecate 3 (with kx 540 motor)
1 87 tecate 4 (with 330 motor, 250r geometry)
1 83 atc 70
1 Kfx 50
1 kfx 400 ( with 470 parting out bike)
1 78 KZ 1000 ( with 1340 turbo)
1 Aprilia SXV 550 Supermoto
1 01 ZRX 1200 prostreet (sold)
Got The Holeshot
Arm chair racerJust too addicted
I powder coated my frames so the labels are no longer there, but I remember the black label was placed off center (to the left) on the head tube. The clear plastic label with the vin number was on the upper portion of the rectangular part of the down tube.
Just Too Addicted
Arm chair racerJust too addicted
I have an original one, I'll take some pictures this week.
nstyle73
"When in doubt, wind it out"
Feedback: http://www.3wheelerworld.com/showthr...k-for-nstyle73
At The Back Of The Pack
Arm chair racerAt the back of the pack
Thank you.....Originally Posted by nstyle73
3 86 Tecate 3
1 87 tecate 3 (with kx 540 motor)
1 87 tecate 4 (with 330 motor, 250r geometry)
1 83 atc 70
1 Kfx 50
1 kfx 400 ( with 470 parting out bike)
1 78 KZ 1000 ( with 1340 turbo)
1 Aprilia SXV 550 Supermoto
1 01 ZRX 1200 prostreet (sold)
Just Too Addicted
Arm chair racerJust too addicted
These are the only two labels I found on the frame. I looked through the FSM supplement and didn't see any others called out. The front fork tube decal is still in place but you probably can find that placement in a brochure picture.
nstyle73
"When in doubt, wind it out"
Feedback: http://www.3wheelerworld.com/showthr...k-for-nstyle73
Wires, Hoses, & Digital Wizardry.
Got the holeshot
Here ya go:
Red Rider's Sand Machine Updated 07/23/14
At The Back Of The Pack
Arm chair racerAt the back of the pack
I need the black one in the neck.
3 86 Tecate 3
1 87 tecate 3 (with kx 540 motor)
1 87 tecate 4 (with 330 motor, 250r geometry)
1 83 atc 70
1 Kfx 50
1 kfx 400 ( with 470 parting out bike)
1 78 KZ 1000 ( with 1340 turbo)
1 Aprilia SXV 550 Supermoto
1 01 ZRX 1200 prostreet (sold)
First Time Rider
Arm chair racerNew to the board
i was just going to start a thread about this...what about chain slack label? gas ratio label? theres a couple others i cant think of...
Power User
Got the holeshot
You mean like this complete set of labels:
http://www.ebay.com/itm/KAWASAKI-TEC...d72a7f&vxp=mtr
looks like these stickers were just slapped on there where ever...
86 T3
84 T3
86 KX250
At The Back Of The Pack
Arm chair racerAt the back of the pack
I have 2 sets, but it doesn't have the black one.
3 86 Tecate 3
1 87 tecate 3 (with kx 540 motor)
1 87 tecate 4 (with 330 motor, 250r geometry)
1 83 atc 70
1 Kfx 50
1 kfx 400 ( with 470 parting out bike)
1 78 KZ 1000 ( with 1340 turbo)
1 Aprilia SXV 550 Supermoto
1 01 ZRX 1200 prostreet (sold)
Just Too Addicted
Arm chair racerJust too addicted
Huh, I was wondering if my black label was slapped on after the fact, but apparently no one at Kawasaki thought to put them on perfectly vertically. I have seen the gas ratio decal on the tank more like the Honda's on the neck, but the FSM shows it on the rear fender. Chain slack goes on the left side of the fender under the seat. To be honest my from the factory fenders don't have any of those decals and there isn't a fade or anything showing that they were there, so they didn't get put on or were taken off shortly after new as the original fenders are different than the NOS ones.
nstyle73
"When in doubt, wind it out"
Feedback: http://www.3wheelerworld.com/showthr...k-for-nstyle73
Wires, Hoses, & Digital Wizardry.
Got the holeshot
I always removed all of the warning labels as soon as I got the new bike home from the dealer for that very reason. Of course, the last new bike I brought home frome the dealer was my '86 250R. I can only imagine the amount of warning labels plastered all over current ATVs.
Red Rider's Sand Machine Updated 07/23/14
Just Too Addicted
Arm chair racerJust too addicted
This may not be the place for this and don't mean to thread highjack, but here are some OEM fender differences. There may be a slight difference by the master cylinder window as shown in the FSM, but my fenders do not have the rivets there so I did not include that area. Notice the factory used rivets for the document holder rather than the bolts available through Kawasaki as replacement parts. Other members may have better pictures or better fenders with more detail.
nstyle73
"When in doubt, wind it out"
Feedback: http://www.3wheelerworld.com/showthr...k-for-nstyle73
Power User
Got the holeshot
There is a Studly forum member that has or makes stickers, labels & graphics.
I need help, Blue something? I am drawing a blank, someone will chime in.
Email- onformula1@hotmail.com Rebuilt, Revalved, custom springs, lowering, forks & shocks, Custom Suspension, all brands, 2-3-4 wheeler's- PM or Email with questions.
***Check out my album for cool pictures*** http://www.3wheelerworld.com/album.php?albumid=2527
As always- Everything I post is IMHO.
Power User
Got the holeshot
Found it-
Bruce (blue27)
http://www.bluelinedecals.com/
He may be able to help.
Email- onformula1@hotmail.com Rebuilt, Revalved, custom springs, lowering, forks & shocks, Custom Suspension, all brands, 2-3-4 wheeler's- PM or Email with questions.
***Check out my album for cool pictures*** http://www.3wheelerworld.com/album.php?albumid=2527
As always- Everything I post is IMHO.
Reply With Quote