//ArrowChat Code
Page 4 of 4 FirstFirst ... 2 3 4
Results 46 to 53 of 53

Thread: Replacing 350x countershaft seal

  1. 11-26-2017, 02:42 PM #46
    barnett468
    barnett468 is offline FACT ! I have no edit button Arm chair racerThe day begins with 3WW
    Join Date
    Jan 2013
    Location
    minnesota
    --
    5,911
    Quote Originally Posted by DDQ View Post
    I am going to keep a careful eye on it and give it a shot.

    Attachment 247583
    Why, just so you can watch it leak from where it peeled the rubber off of the outside?


    PREVIOUS KAWASAKI INTERNATIONAL R & D PROJECT ENGINEER AND ATV DEPARTMENT SUPERVISOR AND THE ONLY PERSON ON 3WW WITHOUT AN EDIT BUTTON OR A STAR
    Reply With Quote Reply With Quote
  2. 11-26-2017, 02:45 PM #47
    DDQ's Avatar
    DDQ
    DDQ is offline At The Back Of The Pack Arm chair racerAt the back of the pack
    Join Date
    May 2015
    Location
    Aberdeen, NC
    --
    414
    I rode it for about 10 minutes this morning and it didnt leak a drop.
    Reply With Quote Reply With Quote
  3. 11-26-2017, 02:46 PM #48
    barnett468
    barnett468 is offline FACT ! I have no edit button Arm chair racerThe day begins with 3WW
    Join Date
    Jan 2013
    Location
    minnesota
    --
    5,911
    Quote Originally Posted by DDQ View Post
    I used a 'bit' more heat on the case...
    Heating a case to install a seal is a complete waste of time.


    PREVIOUS KAWASAKI INTERNATIONAL R & D PROJECT ENGINEER AND ATV DEPARTMENT SUPERVISOR AND THE ONLY PERSON ON 3WW WITHOUT AN EDIT BUTTON OR A STAR
    Reply With Quote Reply With Quote
  4. 11-26-2017, 02:48 PM #49
    barnett468
    barnett468 is offline FACT ! I have no edit button Arm chair racerThe day begins with 3WW
    Join Date
    Jan 2013
    Location
    minnesota
    --
    5,911
    Quote Originally Posted by DDQ View Post
    I rode it for about 10 minutes this morning and it didnt leak a drop.
    Good, it might have just peeled a little of the outer edge off then.


    PREVIOUS KAWASAKI INTERNATIONAL R & D PROJECT ENGINEER AND ATV DEPARTMENT SUPERVISOR AND THE ONLY PERSON ON 3WW WITHOUT AN EDIT BUTTON OR A STAR
    Reply With Quote Reply With Quote
  5. 01-19-2021, 09:18 AM #50
    badlarry's Avatar
    badlarry
    badlarry is offline New to the board Arm chair racerNew to the board
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    33
    Looking for this seal.
    Any part number available?
    Sources that have a replacement?
    Reply With Quote Reply With Quote
  6. 01-19-2021, 09:21 AM #51
    badlarry's Avatar
    badlarry
    badlarry is offline New to the board Arm chair racerNew to the board
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    33
    Seal number please.
    91005-HA5-000 is not savable
    Reply With Quote Reply With Quote
  7. 01-19-2021, 10:28 AM #52
    shortline10's Avatar
    shortline10
    shortline10 is offline Power User The day begins with 3WW
    Join Date
    Jul 2009
    Location
    South Florida
    --
    6,725
    22x35x8 seal , eBay has plenty

    https://www.ebay.com/itm/TC-22-35-8-...EAAOSwlY1ZFesN
    78 atc 90/180cc Dickson Full Suspension
    76 ATC90/180cc Nicholson
    77 atc 90 Dickson Full Suspension
    84 KLT 110/123cc Powroll Racer from 80s
    87 atc 125m stock
    84 atc 200x Curtis Sparks
    84 atc 200x Powroll My race bike from 80's
    83 atc70/108cc Powroll blue Xmas Special
    81 atc185s HP-ATC full suspension

    Performance Shop is Open PM me for Service

    My Feedback http://www.3wheelerworld.com/showthr...ck+shortline10
    Reply With Quote Reply With Quote
  8. 01-19-2021, 11:04 AM #53
    badlarry's Avatar
    badlarry
    badlarry is offline New to the board Arm chair racerNew to the board
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    33
    Yes, I was looking at this exact seal... Thank you for your time. I ordered 2
    Reply With Quote Reply With Quote
//ArrowChat Integreation Code //