The seat pan cleaned up nice. Did you use just vinegar or another rust removal product? Thanks for sharing your build.
Sent from my iPhone using Tapatalk
The seat pan cleaned up nice. Did you use just vinegar or another rust removal product? Thanks for sharing your build.
Sent from my iPhone using Tapatalk
Thanks for the tip on partzilla. That is much easier and really helpful. Which led me to search for the seat foam.
http://hi-flite-usa.com/product/hond...ver-kit-e163k/
Might just get a new for the price.
Sent from my iPhone using Tapatalk
Yea kind of hard to beat that when used seats go for that kind of price on ebay.
I’ve received the pipe, head and cylinder:
I’d like to blast and paint the cylinder. Can I use sand or glass? Tape off all the gasket areas really good? I’ve never done it, so any suggestions would be helpful.
As far as painting, is it safe to have them powdered?
Sent from my iPhone using Tapatalk
Buy some gorilla tape and tape off all the machines surfaces and don’t be shy with the tape. Make sure it adequately covers and stick to all areas. You don’t want to inadvertently blast your new cylinder. I would use glass bead to blast and yes, powder is perfectly fine to use.
Thanks, that’s working out sweet. I think...got a tiny bit of glass through the tape. I thought I taped it well enough but apparently not. Hopefully it’s ok. I blew it out real good.
To remove those black rubbers on the head, I was going to heat them up. Sounds good? I actually need a few more. Anyone know their purpose? Keep the integrity of the fins? Maybe their not crucial and I can stop looking.
Got the bearings and just realized I need seals. Next time a get 2-days off, I’ll open it up. Thanks again.
Sent from my iPhone using Tapatalk
Those rubber bits are just wedged in there. You should be able to pull them out with some needle nose, but heat may help that process. Their purpose is what you said, keep the integrity of the fins and vibration dampening. Put them back in when you are done powdering.
78 atc 90/180cc Dickson Full Suspension
76 ATC90/180cc Nicholson
77 atc 90 Dickson Full Suspension
84 KLT 110/123cc Powroll Racer from 80s
87 atc 125m stock
84 atc 200x Curtis Sparks
84 atc 200x Powroll My race bike from 80's
83 atc70/108cc Powroll blue Xmas Special
81 atc185s HP-ATC full suspension
Performance Shop is Open PM me for Service
My Feedback http://www.3wheelerworld.com/showthr...ck+shortline10
Would you know where I could find some? I’d need 4 each of these:
I checked eBay-that’s not going to happen. 25$ plus shipping for 3-pieces and one is literally in 3-pieces. Maybe I could cut them out of thick rubber.
Edit: changed 2 to 4
Sent from my iPhone using Tapatalk
Last edited by Jd110; 12-14-2018 at 09:00 AM.
I may have some , I can check this weekend .
78 atc 90/180cc Dickson Full Suspension
76 ATC90/180cc Nicholson
77 atc 90 Dickson Full Suspension
84 KLT 110/123cc Powroll Racer from 80s
87 atc 125m stock
84 atc 200x Curtis Sparks
84 atc 200x Powroll My race bike from 80's
83 atc70/108cc Powroll blue Xmas Special
81 atc185s HP-ATC full suspension
Performance Shop is Open PM me for Service
My Feedback http://www.3wheelerworld.com/showthr...ck+shortline10
Crank checked out to be true and within spec.
Is the kicker return spring normally at an angle? I didn’t get a picture before it separated on me. I think it hooks on the dowel pin but not sure. I can’t tell from the manual picture. Anyway, I tried a test fit and it appears to be really close to the other side case. There is a tiny mark on that side where it possibly touched the side of case, so I’m thinking that is the normal position it sits but thought I’d ask.
Got that back in.
I’m putting the top end together, tonight and realized one of the head bolts are bent. When it went to get bored, they asked if It had been dropped upon disassembly because the cast in sleeve was ready to fall off. So it was re-sleeved. Now I need at a new bolt.
Also, the wrong seat was delivered, today. Looks like it’s for a 2nd or 3rd gen. Other than that, I’m lovin’ this baby!! Oh, got my tires mounted last night on some fresh gold!!
Judgment day is right around the corner.
Sent from my iPhone using Tapatalk