//ArrowChat Code
Results 1 to 7 of 7

Thread: 1981 110

  1. #1
    Join Date
    Nov 2018
    Location
    IN
    --
    30

    1981 110

    If anyone has a picture of how the wiring harness is routed I’d appreciate it. Wrapping up my restoration and when I bought the trike the harness was missing. I know the CDI goes on the upper tab by my arrow, Still tracking down the rubber holder for it. Im just not sure on the rest , there’s another tab below that but it’s been damaged from what I can tell. Also not 100 percent sure on the routing of the brake cable through the forks .
    Any help would be appreciated.

    Thanks Click image for larger version. 

Name:	528E4644-C061-4AF1-878D-DD5D98FFF6C4.jpeg 
Views:	11 
Size:	690.2 KB 
ID:	257620

  2. #2
    Join Date
    Nov 2015
    Location
    Davenport iowa
    --
    1,144
    The harness needs to pass through your frame. The opening you see up towards the front of the trike on that side and it comes out of the opening above your top back mount, once you do that it will all make sense. The front brake cable runs down where you have the harness now.

    Show us a pic of how you have your front brake cable now
    Last edited by DAM shop; 03-06-2019 at 06:52 PM. Reason: More instructions
    90 nickolson Bored and Stroked "The Good"

    Big Bore 110 Pauter frame "The Bad"

    90 Bored and Stroked “vey’s frame” "The Ugly"

    110 JSC frame Bored and Stroked
    flat track build. “Shop trike”

    1974 original 90 X 2

    1974 Original 70.

  3. #3
    Join Date
    Nov 2018
    Location
    IN
    --
    30
    Click image for larger version. 

Name:	A1AB3E22-A8F2-450E-8F74-89565FB95B51.jpg 
Views:	9 
Size:	1.09 MB 
ID:	257621
    Click image for larger version. 

Name:	7B51255C-AC96-4FC2-8495-4A7E89BBCD5C.jpeg 
Views:	10 
Size:	2.17 MB 
ID:	257622

    Coming through the frame makes total sense now ! Thanks . I’ve restored or replaced everything on this bike other than the original OEM plastics . Including engine rebuilt from bottom to top so getting excited for the finish line .

  4. #4
    Join Date
    Nov 2018
    Location
    IN
    --
    30
    One thing just became painfully obvious... I gotta pull the motor to properly run the harness through the frame .

  5. #5
    Join Date
    Nov 2015
    Location
    Davenport iowa
    --
    1,144
    Quote Originally Posted by Yzfireguy815 View Post
    One thing just became painfully obvious... I gotta pull the motor to properly run the harness through the frame .
    You may be able to pull the top rear mount bolt and loosen the bottom, pull the front mount and see if you can swing it out of the way enough.
    90 nickolson Bored and Stroked "The Good"

    Big Bore 110 Pauter frame "The Bad"

    90 Bored and Stroked “vey’s frame” "The Ugly"

    110 JSC frame Bored and Stroked
    flat track build. “Shop trike”

    1974 original 90 X 2

    1974 Original 70.

  6. #6
    Join Date
    Nov 2018
    Location
    IN
    --
    30
    I’ll give that a shot . Thanks

  7. #7
    Join Date
    Nov 2015
    Location
    Davenport iowa
    --
    1,144
    Looks good, nice job. Your brake cable routing looks to be correct I also think that the throttle cable routes the same way.
    90 nickolson Bored and Stroked "The Good"

    Big Bore 110 Pauter frame "The Bad"

    90 Bored and Stroked “vey’s frame” "The Ugly"

    110 JSC frame Bored and Stroked
    flat track build. “Shop trike”

    1974 original 90 X 2

    1974 Original 70.

//ArrowChat Integreation Code //