//ArrowChat Code
Results 1 to 5 of 5

Thread: 1986 ATC Big Red 250ES Clutch Help

  1. #1
    MN250R's Avatar
    MN250R is offline At The Back Of The Pack Arm chair racerAt the back of the pack
    Join Date
    Jun 2003
    Location
    Minnesota
    --
    285

    1986 ATC Big Red 250ES Clutch Help

    Hello,
    I recently changed out my one way bearing with my clutch on my big red. I figured since i was in there, I would replace the clutch pack. I followed my manual making sure the washers were all put back in the correct place etc.
    Now when i shift it into gear, it jumps forward and wants to go. I tried adjusting the play (increase decrease). I have taken it apart 3 times and i get the same results. Starts right up, when i shift it into gear, it jumps forward and wants to start moving. Im at a loss. Any help would be great. Thanks!
    1986 ATC 350X
    1986 ATC Big Red 250ES

  2. #2
    Join Date
    Jul 2009
    Location
    South Florida
    --
    6,722
    You put the one way bearing in backwards .
    Easy way to tell if it’s correct is you push the Atv forward in gear not running does it turn the motor over piston included ? And when you push it backwards in gear does it roll freely ? If opposite then it’s installed backwards .
    The China aftermarket bearings are often marked incorrectly .
    78 atc 90/180cc Dickson Full Suspension
    76 ATC90/180cc Nicholson
    77 atc 90 Dickson Full Suspension
    84 KLT 110/123cc Powroll Racer from 80s
    87 atc 125m stock
    84 atc 200x Curtis Sparks
    84 atc 200x Powroll My race bike from 80's
    83 atc70/108cc Powroll blue Xmas Special
    81 atc185s HP-ATC full suspension

    Performance Shop is Open PM me for Service

    My Feedback http://www.3wheelerworld.com/showthr...ck+shortline10

  3. #3
    MN250R's Avatar
    MN250R is offline At The Back Of The Pack Arm chair racerAt the back of the pack
    Join Date
    Jun 2003
    Location
    Minnesota
    --
    285
    Thx for the reply! When I shift it into first, it rolls forward, you can hear the drivetrain slowing turning. but I can't push it backwards in first, it won't move.
    1986 ATC 350X
    1986 ATC Big Red 250ES

  4. #4
    Join Date
    Jul 2009
    Location
    South Florida
    --
    6,722
    Definitely installed backwards then


    Quote Originally Posted by MN250R View Post
    Thx for the reply! When I shift it into first, it rolls forward, you can hear the drivetrain slowing turning. but I can't push it backwards in first, it won't move.
    78 atc 90/180cc Dickson Full Suspension
    76 ATC90/180cc Nicholson
    77 atc 90 Dickson Full Suspension
    84 KLT 110/123cc Powroll Racer from 80s
    87 atc 125m stock
    84 atc 200x Curtis Sparks
    84 atc 200x Powroll My race bike from 80's
    83 atc70/108cc Powroll blue Xmas Special
    81 atc185s HP-ATC full suspension

    Performance Shop is Open PM me for Service

    My Feedback http://www.3wheelerworld.com/showthr...ck+shortline10

  5. #5
    MN250R's Avatar
    MN250R is offline At The Back Of The Pack Arm chair racerAt the back of the pack
    Join Date
    Jun 2003
    Location
    Minnesota
    --
    285
    All fixed! Thanks for your help. The China one way bearing was stamped on the wrong side!
    1986 ATC 350X
    1986 ATC Big Red 250ES

//ArrowChat Integreation Code //