What do you call these?

[Shep1970]

Learned something new today, don’t use metal washers as part of a mold to help make a tighter fit on something......
Won’t just slide off (rubber too tough) and need to cut the washer off which can’t happen.

Now gotta find those plastic washers i have somewhere...
Atleast half the mold is still good.....what the heck was I thinking...

Shep


Sent from my iPhone using Tapatalk

[Shep1970]

Ok- done. Nice tight (er) fit. Now I’ve got a question for you, the opening (top) it’s like a 1/4 inch opening I believe for just 3-wires? Want me to close that up a bit? Or leave as is
I could make that end solid 1/8 thick rubber like cap that u could just make holes for the wires (water tight) if that makes sense?






Shep


Sent from my iPhone using Tapatalk

[El Camexican]

Standby.....

[Shep1970]

I Wasn’t thinking that you’ve got, or that there’s a sleeve that goes in there too. Probably best bet is to leave it like it is. (The opening) top
I think.

Shep

And smudge some silicone around the sleeve if need be/ there probably was some from the factory, maybe.
Easy to close it up a bit though

[ps2fixer]

I suspect the harness tubing went inside of the boot, and harness taped around it to "seal" it and hold the tubing in. Could be wrong though, not a type I've worked with much.

[Dirtcrasher]

Order a nylon washer assortment from somewhere, I've got allot of odd balls but an assortment would be the balls...

[El Camexican]

Seems I just lucked out and got an OEM part in good condition off of eBay. As you can see in the photo it’s a loose fit right from the factory. The SHEATH on the wiring which contains four strands is .300 inch in diameter. If you can reduce the sleeve ID slightly it would be a much better fit.

[Shep1970]

Ok sounds good,
What I’ll do is send you 5 of the exact (top size) opening copies there just under 5/16”
-I made a few-

Now (tonight) I’ll slim down the (top size) opening and send 5 of those too.

U can pic the one that works better and have lots of extras


I should be able to ship em’ out on Friday
Same return address correct?

Shep


Sent from my iPhone using Tapatalk

[El Camexican]

Ok sounds good,
What I’ll do is send you 5 of the exact (top size) opening copies there just under 5/16”
-I made a few-

Now (tonight) I’ll slim down the (top size) opening and send 5 of those too.

U can pic the one that works better and have lots of extras


I should be able to ship em’ out on Friday
Same return address correct?

Shep


Sent from my iPhone using Tapatalk

I tossed a paper with the shipping address in the box.

Please PM me your paypal address and the damage + shipping.

Thanks!!!

[Shep1970]

Yup, I see the paper. You owe me nothing, we’re all set.

Shep

[Shep1970]

One last picture of the kids before they get divided up tonight. Think I’ve seen enough of these for a lifetime or a while anyway.....EL- your group of 10 will be shipped in a touch of baby powder that’ll wash off.


Only one fail in the bunch/it was the first test on how many grams mix I needed to fill mold. First one came up short.

Shep


Sent from my iPhone using Tapatalk

[ps2fixer]

About 33 sets, that's some pretty good mass producing there xD.

[El Camexican]

Finally got these home! Thank you Shep!!!! Will try to install one ASAP.



Long story, but basically a lot of people did a lot of favors and everything I’ve had mailed to TX since February arrived to my place today.

Also got all the wires ps2 recommended, I should be good to go on my Tri-Z ignitions.

[ps2fixer]

Good luck, hopefully all works out well for you =)

[Tri-Z 250]

I could use a few of these, great idea.