//ArrowChat Code
Results 1 to 7 of 7

Thread: 85 350x rebuild

  1. #1
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    31

    85 350x rebuild

    I bought a 1985 350X completely disassembled in parts and boxes in the mid-90s .while I was riding my 86 350 x another X! rider said he had one completely disassembled for a rebuilt so now it's been sitting around for over 30 years and I'm about to rebuild the engine that was completely disassembled I looked up the crank bearings andClick image for larger version. 

Name:	IMG_20190720_151236.jpg 
Views:	49 
Size:	2.90 MB 
ID:	265975 the counter balance bearings and a seal to put the two case halves together and that's about $160 for bearings I figured I'd start with the engine at this point.
    With the parts that I have collected over the years I think I have just about everything I need except some seals and gaskets like swing arm bearings axle bearings an axle shaft if anyone has an axle for the rear of a 350 x let me know. I'm pretty confident I can put the engine together I will send the head out in the cylinder out for that type of machine work but the lower end should be fairly simple with the manual in previous engine work that I have done. My 86 is completely polished and chrome swing arm and all that jazz that I rebuilt in 2000 with a brand new frame from Honda I did not reinforce the frame I just used the brand new frame straight out of the box for my build.
    I spelled them contemplating I'm just putting together with no paint work and writing it as as is or I may completely blast and paint it upon assembly. [ATTACH=CONFIG]265973[/ATTACHEDClick image for larger version. 

Name:	IMG_20190720_151330.jpg 
Views:	46 
Size:	2.24 MB 
ID:	265974]
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_20201213_143250.jpg 
Views:	42 
Size:	2.13 MB 
ID:	265973  

  2. #2
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    31
    Click image for larger version. 

Name:	IMG_20201213_153621.jpg 
Views:	38 
Size:	2.03 MB 
ID:	265976
    Click image for larger version. 

Name:	IMG_20201213_145839.jpg 
Views:	39 
Size:	1.96 MB 
ID:	265977

  3. #3
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    31
    Click image for larger version. 

Name:	IMG_20210131_152813.jpg 
Views:	32 
Size:	1.67 MB 
ID:	266462Click image for larger version. 

Name:	IMG_20210131_152813.jpg 
Views:	32 
Size:	1.67 MB 
ID:	266462Click image for larger version. 

Name:	IMG_20210131_152813.jpg 
Views:	32 
Size:	1.67 MB 
ID:	266462

    All new bearings, seals and gaskets are here

  4. #4
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    31
    Click image for larger version. 

Name:	IMG_20210131_140637.jpg 
Views:	34 
Size:	969.1 KB 
ID:	266463

    Primer is on... Crankshaft going in

  5. #5
    wild200x is offline At The Back Of The Pack Arm chair racerFirst time rider
    Join Date
    Jul 2003
    --
    196
    Looking good and looks like extra front end parts too.

  6. #6
    Join Date
    Nov 2008
    Location
    new hampshire
    --
    31
    Click image for larger version. 

Name:	IMG_20210214_082741.jpg 
Views:	34 
Size:	1.30 MB 
ID:	266698

    Made a bolt to use my crank dampner installer tool pull my crank thru bearing.

    Click image for larger version. 

Name:	IMG_20210214_101144.jpg 
Views:	34 
Size:	1.73 MB 
ID:	266699 to

    Case is ready to seal up.. after shifter drum is installed.. wrong picture appliedClick image for larger version. 

Name:	IMG_20210214_083050.jpg 
Views:	37 
Size:	1.58 MB 
ID:	266700

  7. #7
    Join Date
    Feb 2021
    Location
    Burgh
    --
    12
    Got any lines on a electric start for an X? I have casting capabilities and would produce some if I can get an example to clone?

//ArrowChat Integreation Code //