Yamaha sport quad rims/hub on YTM225DX...

[unclejemima]

There has been some posts in the last few weeks of putting Yamaha sport quad rims/hubs on a YTM225DX.

I just wanted to verify 100% this will work.

I know the blaster hubs are 100% confirmed to work, but has anyone used anything else (Banshee, Warrior or Raptor?)

Would the Banshee/Warrior/Raptor hubs be any stronger than the Blaster?

In regards to rims, do all the named Yamaha sport quads use the same wheel lug spacing, or does each model vary? I was planning on getting a set of Blaster Rear hubs (they are cheap and easy to find) and then stock aluminum rims from a Raptor. Is this a good plan? Will it all bolt up?

Thanks!

[kirby]

There has been some posts in the last few weeks of putting Yamaha sport quad rims/hubs on a YTM225DX.

I just wanted to verify 100% this will work.

I know the blaster hubs are 100% confirmed to work, but has anyone used anything else (Banshee, Warrior or Raptor?)

Would the Banshee/Warrior/Raptor hubs be any stronger than the Blaster?

In regards to rims, do all the named Yamaha sport quads use the same wheel lug spacing, or does each model vary? I was planning on getting a set of Blaster Rear hubs (they are cheap and easy to find) and then stock aluminum rims from a Raptor. Is this a good plan? Will it all bolt up?

Thanks!

there is a difference is the bolt patterns, the warrior, banshee, and raptor are 4-115 and are the same but the baster is different its 4 -110

[honda28]

Blaster is 4-100. You could used tri-z rear wheels they have 4-100 bolt pattern.

[Bryan Raffa]

correct,, blaster/tri-z 4/100,,,

warror/banshee/raptor,yfz ,all sport bikes are all 4/115

they all will work but you have to use the right wheel/hub combo

[unclejemima]

Ok, so the lug spacing is 4/100 for the blaster/tri-z and 4/115 for the others. Good to know.

Has anyone actually used a hub from a warrior/banshee/raptor on the 225DX (or 200E). Is it a direct bolt on like the blaster?

I think I will probably stick to a warrior/banshee/raptor hub/rim combo if it will bolt up. I would like to get aluminum if possible, and it is hard to find in the blaster as most of them I'm finding are steel.

Thanks,

[oldskool83]

i know banshee hubs are the same amount of splines are the 200x/350x, with that being said u should be able to run 300ex/400ex hubs on them to get 4x110 bolt patterns and widen it a little.

i know this cuz a member had banshee hubs on a 200x

[unclejemima]

i know banshee hubs are the same amount of splines are the 200x/350x, with that being said u should be able to run 300ex/400ex hubs on them to get 4x110 bolt patterns and widen it a little.
i know this cuz a member had banshee hubs on a 200x

Really good info. It would make sense that Honda/Yamaha would make something that is universal.

Can anyone else verify this? It sure would make it a-lot easier to find rims if I could also source Honda hubs/rims for my YTM225DX.

Thanks,

[Zuplar]

Has anyone figured out if the honda hubs will fit on the 225? I actually have a set laying around my house, I will try this weekend if someone hasn't already debunked this.

[trizilla]

Has anyone figured out if the honda hubs will fit on the 225? I actually have a set laying around my house, I will try this weekend if someone hasn't already debunked this.

WORN OUT 200x hubs will fit on, but you have to beat them on:D therefore, 200x, 350x etc will fit, as long as there worn.

[bobotech]

Why worn out?

[Zuplar]

Yes, well i tried non worn out hubs, and they did not work. Looks like only Yamaha hubs will fit. Picked me up a set of blaster hubs for $1, so I will be using those.

[Zuplar]

well i did a hub swap. i put blaster hubs on, but then realized i had 400ex wheels lying around. so i ended up using the CNC to make some spacers/adapters. pics below: