Results 1 to 10 of 10

Thread: question about swing arm and the little caps for the sleeve

  1. 03-30-2010, 09:19 PM #1
    QCR77's Avatar
    QCR77
    QCR77 is offline Just Too Addicted Arm chair racerJust too addicted
    Join Date
    Aug 2009
    Location
    SA TX
    --
    538

    question about swing arm and the little caps for the sleeve

    i got on my 350x today to start it and noticed a bunch of play somewhere. so i figured out where it was and took the long bolt out of the swing arm. in between the frame and swing arm there are little caps and inside those caps are a metal spacer for the swingarm and sleeve and also little rubber seals. well, both of the metal spacers are shot(one completely shredded) and the rubber seals are toast too. i cant figure out the name of those pieces and on ebay i found the whole sleeve with the caps but in the picture i can tell that the spacers arent there. anybody know how i can get a couple or make some?
    Reply With Quote Reply With Quote
  2. 03-30-2010, 09:40 PM #2
    QCR77's Avatar
    QCR77
    QCR77 is offline Just Too Addicted Arm chair racerJust too addicted
    Join Date
    Aug 2009
    Location
    SA TX
    --
    538
    manual says pivot side collar?
    Reply With Quote Reply With Quote
  3. 03-30-2010, 09:56 PM #3
    QCR77's Avatar
    QCR77
    QCR77 is offline Just Too Addicted Arm chair racerJust too addicted
    Join Date
    Aug 2009
    Location
    SA TX
    --
    538
    where do these go?
    http://cgi.ebay.com/ebaymotors/SWING...Q5fAccessories
    Reply With Quote Reply With Quote
  4. 03-30-2010, 09:59 PM #4
    RodKnockRacing's Avatar
    RodKnockRacing
    RodKnockRacing is offline Got The Holeshot Arm chair racerJust too addicted
    Join Date
    Jun 2009
    Location
    Tunkhannock,Pa
    --
    904
    inside the swingarm
    1985 200X
    66mm H&S Piston
    Little Bit Bigger Cam
    Bassani Exhaust

    1985 350X With Bassani Exhaust

    1983 Honda 200E (PARTING OUT!!!!)

    1985 Yamaha Tri-Zinger


    My Feedback Threadhttp://http://www.3wheelerworld.com/showthread.php?105185-Feedback-for-RodKnockRacing&highlight=RodKnockRacing
    Reply With Quote Reply With Quote
  5. 03-30-2010, 10:03 PM #5
    QCR77's Avatar
    QCR77
    QCR77 is offline Just Too Addicted Arm chair racerJust too addicted
    Join Date
    Aug 2009
    Location
    SA TX
    --
    538
    Quote Originally Posted by RodKnockRacing View Post
    inside the swingarm
    on the frame side right?
    i think im having trouble understanding because there arent any needle bearings in my swing arm. which would explain why the side collars were obliterated
    Reply With Quote Reply With Quote
  6. 03-30-2010, 10:33 PM #6
    QCR77's Avatar
    QCR77
    QCR77 is offline Just Too Addicted Arm chair racerJust too addicted
    Join Date
    Aug 2009
    Location
    SA TX
    --
    538
    after some research, i think the previous owner/owners might have used one of those bushing sets instead of bearings. really, i wish someone would tell me what i need to buy assuming that all i have is a hollow swing arm and the bolt w/nut that goes through it. i guess i know i need to buy some bearings, but what else? the dust seals? anything else?
    Reply With Quote Reply With Quote
  7. 03-30-2010, 10:58 PM #7
    atc350xer's Avatar
    atc350xer
    atc350xer is offline The Enthusiast. Teaching quads a lesson
    Join Date
    Jan 2010
    Location
    Beaver Falls, PA
    --
    2,666
    I just bought those same bearings... haven't put them in yet though.
    They go inside the actual swing arm, then the caps on the outside.


    Feedback Thread : http://www.3wheelerworld.com/showthr...-for-atc350xer
    Reply With Quote Reply With Quote
  8. 03-31-2010, 09:14 AM #8
    atc350xer's Avatar
    atc350xer
    atc350xer is offline The Enthusiast. Teaching quads a lesson
    Join Date
    Jan 2010
    Location
    Beaver Falls, PA
    --
    2,666

    Is this what you need?

    Did you find your parts yet? I have a used setup...


    Feedback Thread : http://www.3wheelerworld.com/showthr...-for-atc350xer
    Reply With Quote Reply With Quote
  9. 03-31-2010, 10:32 AM #9
    Yamahondaman's Avatar
    3WW Star-Yamahondaman
    Yamahondaman is offline R.I.P. Hey Ron Racing-GIT IT RAG! Got the holeshot
    Join Date
    Jan 2004
    Location
    Palmetto,Florida
    --
    2,300
    Any Brg place has the Brg's .. HK2030 .. same as 200x and 250-r's .. i have some 316L Stainless inserts that go on each side of the swinger after the brg's are installed .. i just sold my Last Stainless Pivot bolt to Ro0sty.. i'll have some more in a week or so.... Ronnie
    "07" DR650 Suzuki Dual Sport
    Reply With Quote Reply With Quote
  10. 03-31-2010, 03:07 PM #10
    QCR77's Avatar
    QCR77
    QCR77 is offline Just Too Addicted Arm chair racerJust too addicted
    Join Date
    Aug 2009
    Location
    SA TX
    --
    538
    Quote Originally Posted by atc350xer View Post
    Did you find your parts yet? I have a used setup...
    in the pic you posted, you are are able to see the pieces i was looking for. i was able to find a new kit (accidentally stumbled into it) that comes with every single piece that is required to attach a swingarm to the frame for $52. it includes the bearings,sleeve,caps,dust seals, washers, the bolt, the side collars ect.. only prob is i found it 1 minute after i had already ordered some bearings (was gonna piece it together). oh well, no biggie. i just have backup bearings now.
    Reply With Quote Reply With Quote
//ArrowChat Integreation Code //