85 Honda 200x weird noise Question

[curtis slawson]

hey my 200x is makein a werid kinda of loud chirping sound when i give it gas dosen't do it when its just ideling runs fine starts fine and not lacking any power did a oil change yesterday found alot of metal shavings in the oil screen iv put a magnet in the oil screen to catch more metal there was alot of stuff on the magnet.

about 4 week's ago i replaced cam chain and cam chain guides and about 2 week after i was riding one day when i was coming home it started to make the werid chriping sound dosent sound to good when going fast sound's realy bad

i guess im gunna have to tear the engine apart to see whats going on any one have any ideal to what causing this sound
wondering..
iv tryed to adjust the valves there in spec thought

Thanks

Videos on 2nd page

[Howdy]

I would check to see if your getting oil to the top end. With debris in the oil it is possible the oil passage got blocked.
Howdy

[shortline10]

Sounds like the lower rod bearing is starting to go . Are the metal shavings magnetic ? Top end shavings would mostly be alum non magnetic and the lower rod would be magnetic shavings .

[curtis slawson]

Sounds like the lower rod bearing is starting to go . Are the metal shavings magnetic ? Top end shavings would mostly be alum non magnetic and the lower rod would be magnetic shavings .

yes they would be metal shaving there stuck to the magnet an other there's stuff that wont sick to the magnet. And for the bottom end bearing there no kocking in the bottom of the engine sound seem to be coming from the top of the motor but i could be wrong

[Howdy]

yes they would be metal shaving there stuck to the magnet an other there's stuff that wont sick to the magnet. And for the bottom end bearing there no kocking in the bottom of the engine sound seem to be coming from the top of the motor but i could be wrong

Shortline is correct. The knocking from the top end could be the piston hitting the head if rod bearing is wore out bad enough. I have seen this a long time ago.
Howdy

[curtis slawson]

Shortline is correct. The knocking from the top end could be the piston hitting the head if rod bearing is wore out bad enough. I have seen this a long time ago.
Howdy

you think i should rip it apart and take a look

[Howdy]

Some time and a gasket kit is cheaper than a totally blown motor.

If it was mine it would already be apart. Some preventative work saves a lot down the road.

Howdy

[350XJEDI]

YES, sounds like you dont have much choice, you might be able to save it , but it may be cheaper to find another moter or do auto-x .. good luck

[curtis slawson]

YES, sounds like you dont have much choice, you might be able to save it , but it may be cheaper to find another moter or do auto-x .. good luck

well i hope it alright iv put alot of time & upgrades & money into it and i couldn't make it a autox thats just to lame for a 200x lol. Dose any one know where i could get a good Crank

[hippyplz]

There is a powroll stroker on ebay right now.

[curtis slawson]

hey i just riped off the cdi cover and the cdi advanser and it has a bad squeak when move back and forth think it could be this too its a little rusty too

[yaegerb]

Can you take a video of it and let us listen to it? I assume it would be noticeable on the video?

[curtis slawson]

Can you take a video of it and let us listen to it? I assume it would be noticeable on the video?

I would but i had takein the motor out in the afternoon. Im gunna try & clean the cdi advanser and throw it back in to see if the AkA chriping squeak is gone cause that is the sound im hearing when driving is the sound that the cdi advanser is makeing the chriping sound when i move back and forth it's a loud chrip squeak sound. and if the motor was running im sure it would be loud cause of the speed the motor is running at it would be spining pretty fast makeing that sound?

i will also take a video was out on the weekend with my buddies he had his gopro on soo ill try to get a video of use driving

[shortline10]

A squeeking advancer isnt going to make metal flakes in your oil screen .

[curtis slawson]

A squeeking advancer isnt going to make metal flakes in your oil screen .

but what if there was already metal shaving in the bottom end and the magnet in put in just picked them up?