I can fit a square peg in a round hole. Just give me a hammer and duct tape!
Arm chair racerJust too addicted
ya it was to much already the stupid thing came with a 50 then a briggs a 125cc 4 stroke then the 250 2 stroke
but it was just lacking that little extra power you need to trow a half pissed adult on his @$$ on take off
and it wasent loud enough to make it known its far from stock
so after a consoltaion with my bong and much thought i figerd it out it s getting a bigger motor again
100_2469.jpg
100_2731.jpg
391316_2631465628840_775178133_n.jpg
Last edited by bcredneck; 08-18-2012 at 07:43 PM.
I can fit a square peg in a round hole. Just give me a hammer and duct tape!
Arm chair racerJust too addicted
here are the last to motor swaps i did with this quad
http://www.3wheelerworld.com/showthr...-to-do-with-it
http://www.3wheelerworld.com/showthr...eed-more-power
Just Too Addicted
Arm chair racerJust too addicted
i don't know, that looks pretty dangerous. what with that extra wheel and all...
86 tri z - might be nearly done throwing money at it! (good thing, the hondas are getting jealous!)
86 250sx - old reliable
83 atc 70-new project for me and the boy
another 82 110
a bunch of golf carts for the wife and kids
-gone but not forgotten-
82? 110 - why did i sell it??
84 225dx - meh, it was a pile
Got The Holeshot
Arm chair racerJust too addicted
Oh boy, here we go again. What kind of parts are you using now, bed frames or garage door hardware?
Roostin' Away
Arm chair racerRoostin Away
is that the 340 Olympic motor that was in the tri-moto frame???
HONDA WITH A WING AND A PRAYER
1984 110 project
1984 125 parts bike
1983 honda 200x
19 85x2honda 200x
1985 honda 250sx
1985 honda 250es
polaris p3 should be a parts bike ***gas tank wanted**
I can fit a square peg in a round hole. Just give me a hammer and duct tape!
Arm chair racerJust too addicted
its a 399 tnt it fits perfect in the frame because the way i droped down the bottom of the frame to put the 250 in there its going to be a single speed i only got room for a pully to chain jack shaft
and its going to have straight pipes i know ill lose power but the motor came with 30 hp when it was new so ill be ok
Roostin' Away
Arm chair racerRoostin Away
it probably doesn't have 30hp any more, its probably so worn outstraight pipes i know ill lose power but the motor came with 30 hp when it was new so ill be ok
HONDA WITH A WING AND A PRAYER
1984 110 project
1984 125 parts bike
1983 honda 200x
19 85x2honda 200x
1985 honda 250sx
1985 honda 250es
polaris p3 should be a parts bike ***gas tank wanted**
I can fit a square peg in a round hole. Just give me a hammer and duct tape!
Arm chair racerJust too addicted
ya i know but its not far off as old as the motor is it hasent been run mutch the cylinders are perfect and it only had about 600 miles on it when the cable broke
it sat behind a shed for a couple decades grass was growing over the skis and i didnt even think they were there till we pulled it out with the truck
I can fit a square peg in a round hole. Just give me a hammer and duct tape!
Arm chair racerJust too addicted
had a little set back some dick stole my clutch and pull start from were i stored the motor
At The Back Of The Pack
Arm chair racerAt the back of the pack
Consult the wise one on the whereabouts.Originally Posted by bcredneck
Just Too Addicted
Arm chair racerJust too addicted
wow, good thing it's only a 399, because a 440 would be ludicrous!!!
seriously though, don't kill yourself just to entertain us!
86 tri z - might be nearly done throwing money at it! (good thing, the hondas are getting jealous!)
86 250sx - old reliable
83 atc 70-new project for me and the boy
another 82 110
a bunch of golf carts for the wife and kids
-gone but not forgotten-
82? 110 - why did i sell it??
84 225dx - meh, it was a pile
Reply With Quote