Got A New 110!

[Gearheadtom]

I picked up a Honda 1982 110 yesterday for $80. The motor wouldn't turn more than a full turn because the cam timing was way off, and after fixing that it had no compression. Figured a bent valve from the timing being off, but it was just a bunch crud under the exhaust valve. Clean and lapped the valves, then cleaned the carb and had it running.
Compression is low and it smokes so I'm going to put in some new rings. The airbox isn't hooked up, and it and the tank look like they're off a newer 110. It needs a pull start, cdi box (I stole the one from my 185 for now), and axel bearings front and rear. The seat is real rough, but there's not a crack in the fenders. Not to bad a deal I don't think.

Here's some pics:

[Gearheadtom]

Picked up some used parts from someone local. Got the pull start, CDI box, and a good rear sprocket (the one on it now is broke), for $70.

[thestud25]

Looks like a decent deal to me.

[mollie8000]

live on 110

[MRSOUND]

The racks alone are worth what you payed for the whole machine

[Gearheadtom]

The racks alone are worth what you payed for the whole machine

That's kinda what I was thinking, with the racks, and the uncracked fenders.

I think I know what at least partialy caused the chain to break. The chain was super tight (even with the horrible rear bearings), I figure they took a link out to tighten an old streched chain, and with the super tight chain they felt no need for the chain tensioner, which I'm also missing.

[atc350xer]

Aren't those gold rims from a blue '83 Christmas special? Wait... are they gold, or just dirty? Good score for the money.

[Gearheadtom]

I tried changing the rear sproket tonight, and after fighting with many rusted bolt/nuts, I finaly got it apart, just to find out that the sprocket that I got as a replacement is from a newer 110, I think. At least I'm not really out anything, the guy threw it in with other parts I bought from him. I ordered new rings last night, and I guess now I'm going to order the chain tensioner and sprocket tomorrow, I guess it's going to have to stay apart for 2 weeks.

I got some pics of the broken sprocket. I would just weld it back together, but there's pieces of the sprocket that are broke and gone.

[Gearheadtom]

Got a bit more work done on this thing. I Got the new rear bearings in the carrier after fixing two holes in it. Just used a couple pieces of tin and JB Weld. It's not really for strengh, but more to keep the mud and water out.
I've got a leak in the tank fixed with more JB Weld, just some old patch material had fallen off, and now I've got some rust remover in the tank (Evaporust) to clean up some of the rust in the tank. There's just a bit of very light surface rust on the sides, and the only real bad rust is down at each lower back corner, where they all rust out.
It probably won't be another week or more until I get my parts in and get it together and driving again.

[Gearheadtom]

I'm in need of another rear axle now. Mine is wore from I guess the bearings seizing and spinning on the axle, so now I've still got play with new bearings. Also the threads for the nut that hold the hub on are stripped out on one side. If I can't find one local, I know a guy with all the proper tools that can probably fix the axle.

[tri again]

I'm in need of another rear axle now. Mine is wore from I guess the bearings seizing and spinning on the axle, so now I've still got play with new bearings. Also the threads for the nut that hold the hub on are stripped out on one side. If I can't find one local, I know a guy with all the proper tools that can probably fix the axle.

I think I have one that somebody simply threaded it down to the next smaller size.

Tacky as heck but super stable, fat threads and it holds tight.

[Gearheadtom]

I think I have one that somebody simply threaded it down to the next smaller size.

Tacky as heck but super stable, fat threads and it holds tight.

If the threads were the only problem, that's probably what I'd do.

[Gearheadtom]

I'm putting my new rings in the motor now. Of the two compression rings, one is a solid color, and one has a silver band on the outer edge. Which one is the top one?

Edit: I did some searching, and from what I could find the one with the silver is the top one, and the darker color one goes below it.

[Gearheadtom]

I got this thing back together and got it running. It doesn't smoke anymore, and has better compression. I think I need a carb now tho, it idles like I've seen 200's idle when the slide is wore. I've checked for air leaks, and found and fixed one, but it still will idle high, the idle low and die. Any way to fix this?

[Gearheadtom]

I've been having trouble getting this thing running right, I know there's nothing I can really do about the idle, but I can't seem to get it to rev either. It's fine in neutral, but when the motor is under load (it's alright on level ground) it doesn't want to rev past 1/2 throttle. The problem is better when I set the needle clip to the richest position. Would the fact that I don't have a filter or air box hooked up cause this? I knew that wouldn't help, but I figured the richest needle position would compensate.
Any suggestions?