Project Childhood Fun Almost finished just need Decals!

[90guy]

We'll got my frame sand blaster primed painted and cleared got the new bearings in the holder. Cleaned my axle up today. Our the carrier in was going to start making progress to realize I can't put the axle in because I don't have my sprocket yet... Stupid me!

[90guy]

Well my sprocket it sitting at the post office can't get it until Saturday due to the silly hours they are open here. Shock covers showed up today for my rear axle. And scored some sweet turbo on the bay a while back not in the nicest shape. But I had them sent to greg at Gkingpolishing. And I got a little teaser of what they look like. These are the legit PCCC not the bapp ones I have lol.

[90guy]

Today It's a rolling chassis until my brakes show up then the magic can happen!

[Joseph Farrow]

Looking Good!

[90guy]

Made some progress this morning. Motor is installed. Painted coil brackets. Ran the wiring and wired everything but the coil. Installed the correct rear brake pads. Made the rear end solid. Cleaned up my chain tensioner. Installed the carb and air filter. Ran the cable not how I want to run it but its a little short. And also decided on my rear tires. have a Turbo in one to see how itll look. I am so excited!

[90guy]

Might be a week more progress is made. Found out my mom has breast cancer so ill be with her as she goes through surgery and stuff. Have contacted motion pro about some custom made cables for it can't wait to get it done!

[90guy]

Made some progress today. Sorry for the pics Its that time of day for my garage haha! I realized when I installed my foot begs they are bent way out of whack. So I need to find a set of nice straight pegs and I also broke my tank strap So I need to find a nice tank strap for it. But she is just about ready to be fired up,. I can't wait to hear this mean machine run!

[shortline10]

Why cant you just straighten the bent peg ?
Remove the rubber and use a long piece of pipe slipped over the bent peg and bend away . 5 minuet fix .

Made some progress today. Sorry for the pics Its that time of day for my garage haha! I realized when I installed my foot begs they are bent way out of whack. So I need to find a set of nice straight pegs and I also broke my tank strap So I need to find a nice tank strap for it. But she is just about ready to be fired up,. I can't wait to hear this mean machine run!

[90guy]

Haha Yeah, I would to that. But this set of pegs has seen better days. That side is welded on it. If I would find a pipe to fit I would probably snap the welds that someone used to put them back together. That old machine I parted out had defiantly seen better days. But I guess its better to give it a try and see what happens.

[shortline10]

The 79 and up atc110 pegs are a better choice if you buy a set , a lot stronger .

Haha Yeah, I would to that. But this set of pegs has seen better days. That side is welded on it. If I would find a pipe to fit I would probably snap the welds that someone used to put them back together. That old machine I parted out had defiantly seen better days. But I guess its better to give it a try and see what happens.

[shortline10]

Need to install the axle spacers , I like them with a big butt

[90guy]

sounds good thanks for that information! Haha I do to. I was wondering would I have to split the rims to drill them or can I just drill them when they are together?

[shortline10]

Defiantly drill them while their together .

sounds good thanks for that information! Haha I do to. I was wondering would I have to split the rims to drill them or can I just drill them when they are together?

[90guy]

Ok just wanted to make sure haha. I had a heck of a time getting those rims to seal up and stop leaking air. It looks kinda sad without that fat back end like your machines have! haha

[90guy]

This ones for you Mike, Just joined the Fat rear club! haha I love the looks of it!