1985 Honda 250SX exhaust question?

[bumsted200s]

Looking for some help searching for Honda '85 250SX exhaust. I've known of supertrapps, even seen some on youtube video once. I'm on eBay 24/7 nothing there. So other then hacking on a slip-on muffler are there options available? Thanks in advance

[shovelryder]

Most everyone I know thats gone aftermarket has gone back to stock shrotly after......They sound cool though!

[Flyingw]

yep, aftermarket usually drives a jetting change and they are loud.

[bumsted200s]

Not to be offensive or to make fun of both your reading skills, but was looking for where I could purchase different exhaust. I am fully aware of jetting and being loud.

[Dave8338]

Here is an option or two: http://www.bikebandit.com/exhaust-ac...424?m=1913&f=3

Jetting is a "fun" process. The fun starts when you get it jetted correctly and lasts for as long as you have the machine. Do it right and don't look back... unless it is to see where everyone else is. HAVE FUN AND GOOD TUNING TO YA !

[Flyingw]

I only come here for the pictures..... Never said I could read but Ebay is about the best bet.

[dustrunner]

hay flyingw i jus got don with mi hooked on foniks u want it ? it reely helped me out....

[Flyingw]

Ya I'll take it. I'll do that after if finish my Bubonics training course I'm taking now. Maybe some day I can apply for that manager position at McDonalds

[dougspcs]

This will fit your 250SX..I have this same issue a few years ago and had the replacement 250ES exhaust in the shop.

http://www.ebay.com/itm/ATC-250ES-25...f5b8b6&vxp=mtr

A bit louder than the stock, not much and no jetting changes needed.

[tri again]

This will fit your 250SX..I have this same issue a few years ago and had the replacement 250ES exhaust in the shop.

http://www.ebay.com/itm/ATC-250ES-25...f5b8b6&vxp=mtr

A bit louder than the stock, not much and no jetting changes needed.

Very pretty.

[dougspcs]

Very pretty.

It got the job done..I had to cut the small support bracket from the frame just in front of the muffler and use a hacksaw to knotch in the front connector pipe so the clamp could crush it down to tighten.

But after that it is a dead nuts fit!!

[bumsted200s]

This will fit your 250SX..I have this same issue a few years ago and had the replacement 250ES exhaust in the shop.

http://www.ebay.com/itm/ATC-250ES-25...f5b8b6&vxp=mtr

A bit louder than the stock, not much and no jetting changes needed.

Thanks for the link, will look from there.

[ngunter2]

http://www.ebay.com/itm/DG-PERFORMAN...506421&vxp=mtr
early trx250s had the big red and 250sx motor. Just a four wheeler. The exhuast mounts are the same too. Should just bolt right up.


This one has a spark arrestor.
http://www.ebay.com/itm/87-93-Honda-...55790b&vxp=mtr

[bumsted200s]

http://www.ebay.com/itm/DG-PERFORMAN...506421&vxp=mtr
early trx250s had the big red and 250sx motor. Just a four wheeler. The exhuast mounts are the same too. Should just bolt right up.


This one has a spark arrestor.
http://www.ebay.com/itm/87-93-Honda-...55790b&vxp=mtr

That's good to know, was not aware of that. Thanks

[kebby28]

My buddie just put this same one on his 250es a couple months ago. He mentioned fighting something like the clamp but it sounds nice. Before with his rotted out one, I couldnt even tell what gear I was in riding next to him. It was like following a Harley through the woods