At The Back Of The Pack
Arm chair racerFirst time rider
I recently acquired an 1985 250es and while changing rear bearings I found that it was missing the RH side bearing stopper. Does anyone have one that can take measurements with a caliper and take pics of the measurement . I have a lathe and will be making one. I'm in dire need of this part.
Power User
Teaching quads a lesson
Which bearing stopper do you have? I can never keep straight which one is which
First Time Rider
Arm chair racerNew to the board
should be this one, may want to use your other one to make the other, as they should both be the same............
Power User
Teaching quads a lesson
AHHH but they aren't the same. Two completely different parts.
At The Back Of The Pack
Arm chair racerFirst time rider
Flyingw I am missing the one on the right. Bigred22 he is right. They are different in siz . I think the previous owner may have busted it while changing bearings. I just bought one on eBay and will be making extras just in case.Thanks guys for helping. Luckily I found one on eBay.
Power User
Teaching quads a lesson
Ok good. When you set the bearings in the left axle tube, did you set the bearings all the way down in the tube?
At The Back Of The Pack
Arm chair racerFirst time rider
Flyingw yes I ran the bearings all the way into the left tube. Is it right to drive them all the way in? Also there is a 200 br speedo installation setup on eBay for 165.00 so if there is a place to put it on here someone may want to do so.
At The Back Of The Pack
Arm chair racerFirst time rider
Well I ran into a problem while removing the header bolts. Drilled and tapped the old header bolts out and started bolting out the head and the head stud started pulling out. I backed out the stud and surely pulled about 3\4 of the threads out. So its time to order some timeserts and fix the pulled threads. It was torqued to 30fbs. when it pulled out.
Power User
Teaching quads a lesson
If you look in the manual for the left axle tube bearing installation, it says to use a bearing installation tool. What the manual does not tell you is how deep the bearings are supposed to be set. All the way down is too deep. The bearing tool sets the bearings 10mm below the outside lip of the axle tube. If you drive the bearings all the way down, it shifts the axle to the right.
Power User
Lord of the trike
I have a few sets of these. Should have posted a want ad in the classifieds.
R.I.P. John Swinehart
TRIKEFEST 11, 12, 13, 14, 15, 16, 17, 19
Epic Mikfest 17
86 200x
85 250sx
85 big red
85 atc 70
Fabiodriven- cereal goes in first, then milk.
I’ve got an 8” Grip on a 10” turd... Kyle Kiser
At The Back Of The Pack
Arm chair racerFirst time rider
10-4 flyingw I'll reset them tomorrow. I'm still waiting on the stopper to come in and with the head stud setback it will give me something to do. And thanks captain I'll be sure to do so next time.
Power User
Teaching quads a lesson
Good, I was hoping you hadn't reassembled the rear end yet.
At The Back Of The Pack
Arm chair racerFirst time rider
Was about to and ran into another problem. The new axle I bought is too long and I have to ship it back. This thing acts like it never wants to be put back together!
Just Too Addicted
Arm chair racerJust too addicted
I have a used oem 85 250es rear axle i think it still has the stoppers and nuts if you think you want it make an offer
you know whats right therefore you know what is expected
At The Back Of The Pack
Arm chair racerFirst time rider
Danbur55 thanks. How's 60.00 plus the ride? But give me a couple days so I can resolve the issue with the other.
Reply With Quote