200x idling high

[niftylittleguy]

I picked up a 1984 200x a week ago and i decided to pick up a new carb since it idled high and ran like crap. So after i put the new carb on it now idles even higher. The carb is pretuned so i am not sure what could be making it rev so high. Also there is no air filter on the bike(not sure if that may be the reason for the idle).

[Thorpe]

Well, pre-tuned... That sounds like the problem. No way it can be pre-tuned for all the variables. And by "new carb", I am guessing it's an eBay China junk?

[yaegerb]

Put a filter on and turn the idle screw down.

[niftylittleguy]

Is there a holder for the air filter? or does it just kinda sit in the air box. Also would unscrewing it idle it down?

[yaegerb]

Get one of these.

http://m.ebay.com/itm/UNI-Two-Stage-...249?nav=SEARCH

And this.

http://m.ebay.com/itm/Uni-Foam-Air-F...144?nav=SEARCH

Oil the filter before you put it on (in the service kit) and clean it when it's dirty. I would also suggest an outerwears on the filter but that's up to you.

Yes, loosen the screw to idle it down.

[Leevvii]

I feel for ya mate, I fell for the ebay carby pitfall too, when i 1st decided to restore mine,

they do work, they're just very underjetted for the 200x.

mine was mikuni, came with a 95 mainjet and a 15 pilot, thats not even standard honda carb level jetting, ....they dont tell ya dat!

[Leevvii]

So after i put the new carb on it now idles even higher

check if Air is leaking anywhere in the inlet circuit?

[niftylittleguy]

So I put the old one carb back on but am still having the same issue. When I first start the bike it runs at the right idle. Then after 20 or so seconds it idles EXTREMELY high. If I shove a full rag in the intake it brings it back down to the right idle. I unscrewed the idle screw out a good amount but it did not make a difference. I also have an air filter I put on but it didn't seem to make a difference

[niftylittleguy]

I also made sure that the air box and the boot going to it from the airbox had no leaks. Could out possible be from the head? Could a gasket be bad or the head cracked. Also once I start it, it does not smoke but after it revs up high it begins to pour smoke out of the exhaust

[danbur55]

Check your throttle cable adjustment to make sure it's not holding open.

[knappyfeet]

Check your throttle cable adjustment to make sure it's not holding open.

X2

That may be the problem

Instead of thinking cracked head......remove the throttle cable completely and run it. Once some of,the basics are covered then you can explore further possible conditions.

[efhondakid]

Air leak from the intake to the head somewhere. Start the bike up and spray some carb cleaner around the intake you'll notice a change in idle if the motor sucks in anywhere. My bet is a bad intake gasket.

[niftylittleguy]

X2

That may be the problem

Instead of thinking cracked head......remove the throttle cable completely and run it. Once some of,the basics are covered then you can explore further possible conditions.

Thats what i thought at first but when the bike is started it runs fine for 10-15 seconds. Then it revs up alot on its own, i never touched the throttle.

[oscarmayer]

Could be carb adjustments. Did you check the slide? Adjust the idle screw to lower the slide. Also you should be starting with the choke and after warm, turn choke off. Are you leaving it on? It will cause it to run faster.


Sent from my iPhone using Tapatalk

[niftylittleguy]

Could be carb adjustments. Did you check the slide? Adjust the idle screw to lower the slide. Also you should be starting with the choke and after warm, turn choke off. Are you leaving it on? It will cause it to run faster.


Sent from my iPhone using Tapatalk

The slider is fine. Also ive tried to adjust the screw but there was no difference at all. Its been quite hot out so i have been starting the bike with the chike off. Also the plug has been getting really black.