What are you doing today? Thread

[Shep1970]

The wife talked me into getting a pedicure w/her today.....ya I know, I know, say what u want. Let me tell you though it’s freakin great! First time for me, maybe I’m getting soft around the edges but I may turn this into a once a yr thing.
If you haven’t I recommend it- foot massage and all. A Little embarrassing but hey who cares right...
“No nail polish, nope”. Just wish they served ‘beverages’ while there.


Shep

[plastikosmd]

^ nope, not ready yet. I barely tolerate a handshake, lol

Took the Jeep into the Woods today, and then to the store!
Fun machine

[barnett468]

.
Got my "GERITOL" YZ250 ready for the annual California AHRMA National Vintage Motocross race at Perris tomorrow , and now I am waiting for a guy to come pick up the police bike (below) in a couple hours that I sold him so he can ride it to Florida, then back to his home in New Jersey.

Hey Knappy, I may have some 2014 Harley Police bikes next month with only 20k miles.





.

[knappyfeet]

.
Got my "GERITOL" YZ250 ready for the annual California AHRMA National Vintage Motocross race at Perris tomorrow , and now I am waiting for a guy to come pick up the police bike (below) in a couple hours that I sold him so he can ride it to Florida, then back to his home in New Jersey.

Hey Knappy, I may have some 2014 Harley Police bikes next month with only 20k miles.





.

Those Hondas sure look nice!

[barnett468]

Those Hondas sure look nice!

They are very nice after I'm done working my "magic" on them, and one could easily be yours for the special low, low, 3ww member price of only $1995.00, (plus surcharges and setup fees and destination fees and California Clean Air fees and save the blunt nose Hodag and Furry Orca Seal fees and...).

[plastikosmd]

First, double checked the TS miter for true-ness with 1-2-3-4-1 cut. Caliper indicates within square, dead true.


Then started some cedar coasters from some scrap. I’m not sure if I will cork the backs after epoxy fill

[Scootertrash]

TS = Table saw?

What's a 1-2-3-4-1 cut?

[plastikosmd]

Yes, tablesaw

12341

Mark all 4 sides sequentially

Cut a bit off side 1, spin so 1 is against fence then cut side 2, then 3 etc until u get back to side 1, now cut off a piece of 1, say 1” thick so u can measure each side for taper.

[Scootertrash]

Interesting. I'll have to remember that.

Thanks!

[barnett468]

.

Just in case anyone was curios what the 1st place trophies for the 250 and open class (any size bike) AHRMA Annual Vintage Motocross National Race held at Perris Raceway today looked like.

.

.

[fabiodriven]

Look at you go Barn!

[3 Wheel Drive]

.

Just in case anyone was curios what the 1st place trophies for the 250 and open class (any size bike) AHRMA Annual Vintage Motocross National Race held at Perris Raceway today looked like.

.

.

Now only if you can earn that “Edit Button”.....

[barnett468]

Now only if you can earn that “Edit Button”.....

"Edit Button...I don't need no stinking edit button!"
.

[barnett468]

.
OOPS....POST CORRECTION CUZ I AN'T GOTS ME NO EDIT BUTTONZ.

"Edit Button...I don't need no stinking edit button!"

should read:
"Edit Button?...I don't need no stinking edit button!"



Damn it Barns...there go my clean new shorts!

...

.

[3 Wheel Drive]

Do you have any videos of your races where you wheelie across the finish line? I’m starting to think you just took pictures of the other guys 1st place trophies.