Registered User
Arm chair racerAt the back of the pack
my swingfer is simply not coming out ive lubed and sprayed for days and pounded and pounded with a sludgeand this thing wont move!!!!! (20 pound sludge
Just Too Addicted
Arm chair racerJust too addicted
If it hasn't come out yet, it probably won't. You'll need to cut it in pieces between the swingarm & frame. If you've been pounding on it, you'll need a new bolt anyway. Plan on spending $50 for the bolt through Honda plus new bearings, bushings & seals. Good luck!
Registered User
New to the board
I have a new bolt and nut I just orderd for my 86 250r and am not going to use it. If it will work on yours PM me will sell it for $30 and some shipping. the bolt is for a 400EX but is the same as 250r. I can send you the sizes if intersted.
Got The Holeshot
Arm chair racerJust too addicted
If a sledge won't move it, you'll have to cut the axle out as mentioned above, and have the remains pressed out.
First Time Rider
Arm chair racerNew to the board
wait before you start cutting you could try to drill it out with a big drill
At The Back Of The Pack
Arm chair racerFirst time rider
If it's a 200x the 250r bolt is bigger. 200x or 350x 14mm 250r 15mm
I you need a swing kit I sell them for the 83/85 200x, 86/87 200x, 85/86 350x
out of used bolts.
Just Too Addicted
Arm chair racerJust too addicted
Sounds like a good price to me.
http://cgi.ebay.com/ebaymotors/ws/eB...sPageName=WDVW
Time to break out the sawzall or torch, huh?
Good Luck!
Just Too Addicted
Arm chair racerJust too addicted
SAWZALL!! is the way out.
Sam from Florida
1985 BIGRED $ 200X
Check my feedback before buying from me
Arm chair racerJust too addicted
I had problems with a bolt on a 200x before.....what i ended up doing was heating the swingarm (where the bolt goes through) and beating the h*ll out of the bolt.....it finally broke loose! if that doesnt work....i dont know what to tell you!
Currently Trikeless!!!
Got The Holeshot
Arm chair racerJust too addicted
If you must resort to cutting, forget the torch and sawzall. Use a small angle grinder with a 1/16 disc. It's a much faster system, and will have better results.
New to the board
Arm chair racerNew to the board
go to Napa or some other parts store and see if they have any stuff called Aero Kroil it is in and orange can. That stuff is great. The bolt will mushroom at the end and you will never get it out. good luck, been there.
Traveler - AK
Within Arms Reach Of The Master
Arm chair racerLord of the trike
Air chisel never fails.
I used to be a slave to the sledge myself untill I was going nuts over the same project and a buddy came over with his air chisel and drove it out in about 5 seconds.
Last edited by OldSchoolin86; 08-28-2004 at 08:11 PM.
'02 Honda 416ex - A seasoned blend of 11 herbs and spices
'04 Honda Recon - The yard machine and snow plow
'88 Honda CR250R - Another chapter in my torrid all terrain affair
Power User
The day begins with 3WW
Air chisels are great, I've sheared the top off of a Chevy Sprint with ours lol.
Center punch and a mall (sledge
My Feedback 85 TECATE 500 08 Honda 450R
At The Back Of The Pack
Arm chair racerAt the back of the pack
If you still need a bolt let me know. As far as kroil I believe in it, and won't use anything else. I got a 110 front axle soaking now for 2 weeks, it keeps disapearing so I keep spraying it on.
'02 ranxher 4x4 '83 big red '84 110, '86trx70 project, '85 bigred project
Reply With Quote