Power User
Roostin Away
ok ive got a 5500mx and a 7500. we didnt even bother with the mx yet but we have been messing around with the 7500. we cleanded the carbs put new gas in and we can get it to run but no long at all or good. any one got any tips to gettin these things running? or where to get manuals? that would help alot. i think we just need to get the carbs adjusted right.
1974 atc 90 project underway cuzzztom
1985 atc 110 for sale
84 200s all original got off the first and only owner
new carb
maybe putting my 200x cam in it but not sure
old trike
1985 200x
12.1 piston
oil cooler kit
white bors cam
super trapp exhaust
uni clamp on air filter
350x front end
Clean enough to eat a potpie off of
Teaching quads a lesson
Manuals you can get through denniskirk in the snowmobile section.
Last edited by 84250r; 01-02-2005 at 06:56 PM.
R.I.P Raven
2006 Yamaha Banshee Special Edition
1996 Honda CBR 600 F3
Registered User
New to the board
Clean fresh gas, top out the oil (if its in a separate tank), pour in some gasline antifreeze (works wonders), and keep a can of Liquid fire or ethanol around for one pull starts.
It sounds like the carbs aren't set right. Like you said
At The Back Of The Pack
Arm chair racerFirst time rider
make sure the fuel pump diaphrams are good if not they won't keep the carbs full
1980 trimoto 125 mods include a ripped seat broke fender and bent handle bars
1981 trimoto 125
1971 suzuki ts 185 it will spank a 200x
1966 gmc 3/4 ton
Power User
Roostin Away
how do they look if they are bad lol?
1974 atc 90 project underway cuzzztom
1985 atc 110 for sale
84 200s all original got off the first and only owner
new carb
maybe putting my 200x cam in it but not sure
old trike
1985 200x
12.1 piston
oil cooler kit
white bors cam
super trapp exhaust
uni clamp on air filter
350x front end
Power User
The day begins with 3WW
if they are bad the rubber over the steal mesh will be gone and rotted and it will just be steel mesh..lol the diaphram is normally on the bottem side of the carb on the rotax's if im not mistaken....
1985 Tri-Z-
Originally Posted by mywifeknowseverything
Power User
Roostin Away
k it ran but only for like 5 mins then died and wouldnt start no matter what it was the vaccum line coming from the crank that was leaking replaced that and tada but now it wont start agian im so fin tired of this were getin 8+ inches supposivly tomarrow and this sucker wont run forthe life of me i think im gunna pull my back out starting it.
1974 atc 90 project underway cuzzztom
1985 atc 110 for sale
84 200s all original got off the first and only owner
new carb
maybe putting my 200x cam in it but not sure
old trike
1985 200x
12.1 piston
oil cooler kit
white bors cam
super trapp exhaust
uni clamp on air filter
350x front end
Got The Holeshot
Arm chair racerJust too addicted
Change your spark plugs before you satrt tearing it apart.
"I am going out of this world.....the same way I came in...screaming and covered in blood."
Got The Holeshot
Arm chair racerJust too addicted
Good Luck with it. You might want to see if theres a bunch of gas that somehow leaked down into the case. If there is I've heard it won't run right and probably won't start. I think this may be the problem with my sled but I haven't had a chance to work on it yet...
Are you getting good spark? Compression?
-86 Polaris Scrambler 250r/es - sold
-84 200es Big Red
-92 Ski-Doo Formula Plus 583 -88 Safari 377 -68 Super Olimpique 299
-87 Jeep XJ 5" lift/many other mods-sold
-89 F-150 4" Lift/33s
-90 Acura Integra - '83 Mustang 5.0 convertible (the new project)
Ask me about custom cut decals!
Reply With Quote
