tri moto rear suspension kit pics

[Trikeaholic]

Here is a pic of the kit as it came from Pro-Tec. As you can see, it consists of a cast Aluminium swingarm, a Bilstien shock, a bracket that goes under the rear seat on the frame by the grab bar to hold the top of the shock, and a brake caliper relocation bracket. I have an ad on my hard-drive somewhere for it from 1982. As I recall, the kit retailed for $325 back then, so figure a YT175 was $800 new ($2000 today) and then this kit was another $325 ($700 today) so now you see why they are pretty rare! for $1700 you could get a new ATC 250R!

[350x'inNY]

Nice Holic! If you can't find the scans, I can rescan them for you. I have a mag or two with YT175 Mods, and I know the one uses that same kit for sure and had the ad right in the same section!

Bruce

[BigGreenMachine]

Very cool! I always wondered what exactly was included. Thanks Holic.

[Huffa]

Very cool. Looks in great shape too. I'm anxious to see it on the trike.

[Louis Mielke]

Excelent. Bwahmmaaha!!!!

[atc110]

would the pro-tec kits work on a 125? I don't have either, but I'm still curious.

[trikerider2oo7]

sweet holic...what does it use for a swingarm bearing? it would be hard to find i'd think

[Trikeaholic]

the bearings are just standard size, I got the old ones out, saved one to match up at work tomorrow. I have to make a new swingarm bolt and bushing for both kits still. The kit will work on the 125 and 175, and Im pretty sure the 200 hardtails too, not positive about the 200, but 95% anyway. Huffa, there is a pic of it installed on my 175 under "got a rare part in the mail today" post. This is a second kit I just found.

[350x'inNY]

Wait wait wait.... so you have the one on your 175 AND 2 other kits now? I know the one was listed bad.... did the same guy have 2 of them?


Bruce

[Trikeaholic]

I have one pro tec kit installed on my YT 175
I have one Pro tec kit laying on the bench in my garage

That makes 2 kits, one is being used on my 175 and one just "is". but it depends on what the meaning of "is" is.

Get it?

I also picked up a NOS +6 Durablue axle for the YT 175 from an old pal of mine. Im hoping Blaster hubs fit the splines so I can run some nice Douglas wheels on it.

[edog]

Can you post pics on your 175 ytm?

[Dan Tenn]

Lets see that axle.

[350x'inNY]

the bearings are just standard size, I got the old ones out, saved one to match up at work tomorrow. I have to make a new swingarm bolt and bushing for both kits still. The kit will work on the 125 and 175, and Im pretty sure the 200 hardtails too, not positive about the 200, but 95% anyway. 1.) Huffa, there is a pic of it installed on my 175 under "got a rare part in the mail today" post. 2.) This is a second kit I just found.

1.) Edog... you read much??? Here's a link for you... don't say I never help ya.... http://www.3wheelerworldforums.com/s...ad.php?t=34818

2.) Holic.... When you said "2nd" one I JUST found, I thought you found 2 of them recently. Me bad! I'll keep an eye out for other 175's around for you.

Bruce

[Trikeaholic]

Ya, Edog made me laugh about that too!

[thefox]

Holic, you said that it might fit the Yamy 200 also your giving me some ideas now .