New to the board
Arm chair racerNew to the board
Hi everyone, I was wondering if a 300ex or 400ex cylinder, head, camshaft etc.. will fit on a 200E block. If so what kind of modifications would be needed and how well will the modification work. I want to get more power out of my '82 200e but don't want to buy a sport quad or trike because I like the carrying capacity of a work wheeler.
thanks everyone
1983 Honda ATC200E Big Red (Converted to Quad) "SPARKY"
1982 Honda ATC200E Big Red (Parts Machine)
Cheetah Mini Bike 4.0hp Honda (52 km/h)
Testicles between my toes at the devils backbone
Teaching quads a lesson
Those mods would not work, all you could do is a high comp. piston (12:1), a cobra pipe, re-jet the carb, and gearing.
TF 07,08,09,10,11,12,13,14!
Raffa's IceFest 08, 09, 10,11,13!
SAY IT!!!!!BUD LIGHTS AND RED LIGHTS!!!!!!
Power User
The day begins with 3WW
What he said, thers also 10:1 Wiseco Pistons that do not require Race gas to run, Also i belive www.webcamshafts.com Makes a High Grind cam for it, also theres clamp on filtres, port the head, Bigger carb, pipe, really depends how much you wana spend, i can say from experiance a 200e with a 12:1 piston on race gas will smoke the tires in third gear from a dead stop....and Pulls Like a Runway freightrain.....Originally Posted by hondaatc185S200E
1985 Tri-Z-
At The Back Of The Pack
Arm chair racerAt the back of the pack
Hey Mate,
I have done a biit of research on this as I am modifying my Atc200.
An XR200 top end will bolt right up,no mods required!!Apparently this is a worth while mod.
At The Back Of The Pack
Arm chair racerAt the back of the pack
What other mods are neccessary to bolt on an XR200 top end? I have looked at pics and they look almost identical in the early versions. Does anyone know technical specs to back this up? I too am looking for easy power upgrades for my 185S which is nearly identical to a 200S. My top end went out so now is the time to make her bigger and badder!
Power User
Roostin Away
no mods required.the xr200 complete topend(jug,head,cam,carb,etc) is a direct bolt on.
Signature pic removed,becuase of no helmet.
Just Too Addicted
Arm chair racerJust too addicted
Holy Old thread batman! I think this thread could've stayed right where it was. lol
Shorty
RIDE RED......OR RIDE HOME
TRIKES ARE NOT DANGEROUS......IDIOTS ARE!
RIP
NOS_350X is the most bad-ass person in the world
Power User
Roostin Away
yeah but at least he was doing a little research.
Signature pic removed,becuase of no helmet.
Registered User
New to the board
I recently purchased a underpowered 1983 200e. I’ve read that an xr200 top end will bolt up with no mods. Is this year specific or will any xr200 top end work. I’ve found some on researching (ebay) and a few locally. I appreciate any advice or input.
Power User
Teaching quads a lesson
I'm not sure on the years here. I think that the older, single carb engine is basically the same as the 200E engine. If it is, then I think that those engine parts should work.
Power User
Got the holeshot
You bought the wrong trike if wanting power.
An XR200 camshaft and carb is all you'll get extra performance from the XR parts, don't need a donor head and cylinder. Doing that is gonna move the power curve higher and kinda ruin what the 200E is good for anyway.
A fresh rebuild with a higher compression piston would be the most bang for the buck. Then if you want more acceleration or more top speed a final gearing change will do that. You only get one or the other, but with a dual range transmission it's not such a hard loss to take if it's just a play trike and you'll never pull a trailer with it and higher gearing.
If you decide to throw a bunch of money and time at it anyway, please share your progress and results.
The story of three wheels and a man...
Reply With Quote
