pics of my R (more added)

[wanta86r]

i just added the roll ims footpegs, short track kit and new pro taper fat bars

[250r'en +TCB]

Do you have the complete short track kit on there, or just the tank and shrouds like me???

Anyway damn that thing looks good!!!!

[wanta86r]

Do you have the complete short track kit on there, or just the tank and shrouds like me???

Anyway damn that thing looks good!!!!

I have the complete kit on( lower tripple, rad relocating brackets, tank, shrouds, and rad hoses) however i did not need to change the rad hoses. it turns extremely sharp with the kit installed. it makes it really easy to manuver around the garage

[Yamaha Tri-Moto]

Very sexy machine you got there. Nice work.

[Lomax]

looks good, what pipe do you have on there, I am going to have to invest in a chrome unit for my 85, the old somewhat rusty FMF isnt going to cut it forever

[Aussieduner]

i just added the roll ims footpegs, short track kit and new pro taper fat bars

VERY NICE !!!


Aussie

[250r'en +TCB]

Man I just keep coming back to drool over that machine!!! Where did you get the short track kit and for how much $$$????

Give us the complete list of mods!!

[ChrisD]

Here you are saying how much you like my R, your's is very similar. Now I know why you like mine. Sweet ride!!!

[wanta86r]

Here you are saying how much you like my R, your's is very similar. Now I know why you like mine. Sweet ride!!!

thanks chris, i still really like yours though!

[8atc250r5]

That thing is SWEET!!!!!


Dave

[wanta86r]

Man I just keep coming back to drool over that machine!!! Where did you get the short track kit and for how much $$$????

Give us the complete list of mods!!

Mods:

-powdercoated frame swingarm and misc bracketry
-stock cylinder ported and oringed by esr on 2nd overbore
-alot of misc chrome bracketry
-Hinson clutch components and 89 update kit
-ESR atc 5 pipe silencer and exhaust flange
-ported rad valve and spacer
-38mm airstryker
-K&N filter in box w/out lid
-stainless steel braided brake lines and cables(clutch and throttle)
-ESR aluminum kicker
-Pro Design shifter
-Pro Taper fat bars and universal clamps(CR high bend)
-Roll Ims footpegs with kickups
-Lonestar adjustable axle, bearing carrier, rear wheel hubs and antifade nut
-prm grab bar and swingarm skidplate
-Sidewinder chain and sprockets (ti-moly)
-alot of aluminum polishing(done by me)
-HRC short track kit
-ITP T-9 9x9 rear with 19 inch mxr4 holeshots
-Douglas polished front wheel with Kenda front max

i also just got done rebuilding the front and rear calipers and mastercylinders. i just want to ride it now , but its been 95 every day. (too hot)
i'm going to post some more photos later

[Derrick Adams]

Those footpegs direct bolt ons? What are they from, TRX?

[wanta86r]

Those footpegs direct bolt ons? What are they from, TRX?

the pegs are a direct bolt on. they are for the 86-87 trx 250r, not the 88-89. The only thing i had to do was shorten the straight end of the spring in the footpeg a little.

[wanta86r]

more pics for you

[wanta86r]

this is how it was wheni bought it( not too bad, except for the cracked frame i didn't know about)It was cracked under the gas tank.
and here is the new frame before powdercoat